Main Menu
  • หน้าแรก>>Products>>Control System>>Control System (Wall Mounted Process Control)>>อุปกรณ์วัด Control System (Industrial Grade TDS Controller with Proportional Fertilizer Dosing for H
  • header_20130410111417.jpg

    อุปกรณ์วัด Control System (Industrial Grade TDS Controller with Proportional Fertilizer Dosing for Hydroponics Applications)

    HI 9934

    Industrial Grade TDS Controller with Proportional Fertilizer Dosing for Hydroponics Applications

    HI 9934 is a  wall mounted meter that controls TDS in the 0 to 1999 ppm (mg/L) range through a single set point for dosage of fertilizers. The proportional control can be fine tuned through the time cycle between 0 to 90 seconds and the proportional band from 0 to 400 ppm. Coarse and fine as well as a slope trimmer make for an accurate setting and calibration. A pump or electrovalve can be powered through the terminal. In addition to the set point relay, HI 9934 also provides for an alarm relay. The alarm is activated when the measurements exceed the set point by a user selectable margin in the 50 to 450 mg/L (ppm) range. The alarm also triggers if, due to a malfunction, the continuous dosing time exceeds the operator adjustable period of 1 to 10 minutes. The alarm can be configured in either normally-closed or normally-open position and turned off during maintenance.

    HI 9934 also provides an isolated output signal which is user selectable between
    0-20 or 4-20 mA.

    HANNA instruments four-ring TDS probes with incorporated temperature sensor and DIN connector can be quickly attached to the controller. Readings are automatically compensated for temperature variations in the 0 to 50°C (32 to 122°F) range.

    The extractable terminal wiring is through the side of the meter with washers and grommets. The compartment containing the connections is enclosed behind a fire-retardant ABS panel.


    Range  0 to 1999 ppm (mg/L)
    Resolution  1 ppm (mg/L)
    Accuracy @ 20°C  ±2% f.s.
    Calibration  through “ZERO CAL” and “SLOPE CAL” trimmers
    Setpoint  from 0 to 1999 ppm (mg/L)
    TDS Conversion
    Factor  0.65 mg/L (ppm) = 1 µS/cm
    Compensation  automatic, 0 to 50°C (32 to 122°F) with ß = 2%/°C
    Recorder Output  selectable at 0-20 mA or 4-20 mA (isolated)
    Control  TDS from 0 to 400 ppm and time cycle from 0 to 90 seconds
    Alarm Contact  terminals can be configured as normally open or normally closed (isolated output max. 2A, max. 240V, resistive load, 1,000,000 strokes). The alarm is activated if TDS exceeds by more than the user- selectable interval (0 to 400 ppm) from the set point or due to overdosage
    Dosing Terminals  relay (115 to 240V, max.2A, 1,000,000 strokes) are activated whenever TDS falls below the set point
    Probe  four-ring potentiometric with built-in temperature sensor (not included)
    Power Supply  ±10% 115 VAC or 230 VAC; 50/60 Hz
    Environment  -10 to 50°C (14 to 122°F); RH max 95% non-condensing
    Case Material  fiber-reinforced, self-extinguishing ABS
    Dimensions  221 x 181 x 86 mm (8.7 x 7.1 x 3.4’’)
    Weight  1.6 kg (3.5 lb.)


    HI 70442L  1500 mg/L (ppm) TDS Solution, 500 mL Bottle
    HI 3001D  Flow-thru Conductivity Probe with DIN Connection and 3 m cable

  • Requesting a Quotation and Ordering Products

    131 Thailand Science Park. Innovation Cluster 1 Building,

    Klong 1, Klong Luang, Pathumthani 12120 Thailand. 

    Tel.  02-191-3928 Fax 02-191-3929

    For more information please contact 081-847-6768 (Ms. Nareerat) IDLine: @alltestkit

    E-mail :


    >>Online Quotation Click here<<